2.2.5: Microscopy
-
- Last updated
- Save as PDF
Learning Objectives
Goals:
- Properly use and care for a sensitive scientific instrument.
- Learn the techniques required to prepare cells for viewing with a microscope.
- Gain a sense of the size of cells.
Student Learning Outcomes:
Upon completion of this lab, students will be able to:
- Identify the parts of a microscope and their functions.
- Properly carry, use, and store a microscope.
- Prepare a wet mount slide.
- View and focus specimens under a microscope.
- Determine total magnification of a specimen.
- Locate a specimen if given a slide.
Introduction
In Biology, the compound light microscope is a useful tool for studying small specimens that are not visible to the naked eye. The microscope uses bright light to illuminate through the specimen and provides an inverted image at high magnification and resolution. There are two lenses that magnify the image of the specimen – the objective lens on the nosepiece and the ocular lens (or eyepiece). To determine the total magnification of the specimen, you must multiply the objective lens magnification with the ocular lens magnification.
Scientists and technicians often use light microscopes to study cells. Prokaryotic cells are very simple and lack a nucleus or membrane bound organelles and are small in size. On the other hand, eukaryotic cells are more complicated in that they contain a nucleus and many specialized organelles. A cell’s structure dictates its function; thus, each eukaryotic cell looks very different from the next. This is why a cardiac cell looks completely different from a neuron (brain cell).
It is very important to learn how to handle and use a microscope properly. Review the following rules and tips for using and handling your microscope.
General Rules
- Always START and END with the low power lens when putting on OR taking away a slide.
- Never turn the nose piece by the objective lens.
- Do not get any portion of the microscope wet - especially the stage and objective lenses.
- Use only lens paper to clean microscope lenses.
Cleaning the Microscope
If needed, obtain a small square of lens paper (and ONLY lens paper) and gently wipe the microscope lenses directly across, in this order:
- the lower surface of all the objective lenses
- the ocular lens
- the condenser lens and the light housing
Part I: Finding the Letter
Materials
- Microscope
- Lens paper
- Letter “E” slide
- Stage Micrometer Slide
Procedure
- Always use one hand around the microscope arm and one hand under the microscope base.
- Carry it in a vertical position without swinging, tipping, dropping or bumping the microscope.
- Place the microscope gently on the lab bench with the arm toward you. Never place the microscope near the edge, and never slide it across the table.
Identify the following microscope parts with a partner. Check off each part as you go. If you are unsure about a component, consult your instructor.
- Eyepiece (ocular lens)
- Nosepiece Ring (turret)
- Objective Lenses (low, medium, high power)
- Stage
- Stage Controls
- Iris Diaphragm Condenser Lens
- Light Source
- Light intensity knob (rheostat)
- Coarse Focus Adjustment Knob
- Fine Focus Adjustment Knob
- Carefully plug in and position electric cord to avoid tripping or having the microscope pulled off the table.
- Turn on the microscope and rotate the nosepiece ring (turret) to snap the 10x objective lens in place. Do not use the objective lens to rotate!
- Turn the light control (rheostat) halfway to adjust the amount of light.
- The total magnification you observe when looking through a microscope is the magnification of the ocular lens multiplied by the magnification of the objective lens. Fill out Table 5.1 to indicate the total magnification achieved by each lens.
|
Lens Name |
Objective Lens |
Ocular Lens |
Total Magnification |
|---|---|---|---|
- On the side of the microscope are two knobs, one on top of the other. The larger of the two knobs is the coarse focus adjustment knob . Turn the knob so that the stage goes down as far as it can.
- Clean all lenses with lens paper. Never use paper towels or kimwipes or shirt!
- Obtain a letter “e” slide from your instructor. Draw the “e” in Table 5.2 as you view it with your eyes (not through the microscope).
|
Letter “e” as seen… |
Drawing |
||
|---|---|---|---|
|
with the naked eye |
|||
|
100X total magnification |
|||
|
400X total magnification |
|||
| 1000X total magnification | |||
| 1000X total magnification | |||
| In what direction does the “e” move (as you look into the microscope), when you move the stage to the right? |
- Place the slide on the stage and secure it with the stage clip .
- Use the coarse focus knob to move the stage as high as it can go.
- Use stage adjustment knobs to center the “e” so that the light from the light source can pass through it.
- Looking through the ocular lenses, lower the stage with the coarse focus adjustment knob until the “e” comes into view.
- Use the fine focus adjustment knob to make the image as clear as you can.
- At this point there are different adjustments you can make to improve the quality of the image:
- The rheostat on the side of the microscope controls the intensity of the light. If it is too bright or dim at any time, use this knob to adjust the light.
- The condenser will also adjust the light intensity. The condenser gathers and focuses the light to illuminate the specimen. Only use this if the rheostat failed to improve your image. Move the condenser with the condenser adjustment knob so that it touches the stage. Slowly lower it to improve lighting on your sample. Usually it should be about ½ inch below the stage.
- The iris diaphragm adjusts the aperture of the opening and controls the amount of light that exits the condenser (or illuminates the specimen). You can open and close this aperture, for most purposes it should be fully open, but sometimes partially closing it will increase contrast in the image.
- Draw the letter “e” as it appears through the microscope in Table 4-2. Note the change in orientation. Notice that the LEFT eyepiece can be rotated, but the ocular scale (known as a reticle) stays in the middle of the ocular lens. Note that the RIGHT eyepiece can be rotated, to move the position of the pointer.
- Move the stage slowly to the right. Note what direction the “e” moves as you look through the microscope and record in Table 4-2.
- Move the slide back to the left to re-center the “e”.
- Once the “e” is re-centered and in focus, turn the nosepiece to the 40x objective lens and snap it into place. Use the fine focus to make the image clear. Only if needed, make light adjustments with the rheostat, condenser, or diaphragm. Draw everything you see through the microscope in Table 4-2.
- Once the “e” is re-centered and in focus turn the nosepiece to the 40x objective lens and snap it into place. Use the fine focus to make the image clear ( NEVER use the coarse focus at this or any higher magnification or you risk snapping the slide or worse, snapping the lens!!!) Only if needed, make any light adjustments with the rheostat, condenser, or diaphragm. Draw everything you see in the microscope in Table 4-2. Answer the questions below.
- To use the oil immersion lens, rotate the nosepiece BETWEEN the 40x and the 100x lenses so that the wand containing the oil can reach the slide. Place a generous drop of oil on the slide and snap the 100x objective lens into place. The lens will slide into the drop of oil.
- Use the fine focus to make the image clear. Only if needed, make light adjustments with the rheostat, condenser, or diaphragm. Draw what you see in Table 4-2.
- NEVER return to the 40X objective lens after there is oil on the slide . If you are having trouble focusing using the oil immersion lens, you must go back and use the 10x lens to re-center (turn the nosepiece so that the 40x objective lens is NOT dragged through the oil on the slide). Then go directly back to the 100x lens. If this doesn’t work, the slide must be wiped clean and you should start over.
When finished with the slide, lower the stage and remove the slide. (Do not lower the stage if you are going to view a different slide). Clean the oil off the slide and return it to your instructor.
Part II: Diameter of the Field
Microscopes are for magnification of images too small to be seen with the naked eye. However, they can be used as a tool to estimate the size of the object being viewed. In order to do this, you must know the diameter of each viewing field with each objective lens. You can then estimate how much of the field your object takes in the field and compare this to the measured diameter. For example, let’s say the diameter of field using the 40x objective lens is 0.10 mm. You then view an object using that lens that takes up ¼ of the field of view. You can then estimate that object is ¼ (0.10mm) long or 0.025mm. To determine the field diameter, you will use a stage micrometer slide, which is basically a very fine ruler (usually 2 mm) that is etched onto a microscope slide.
Procedure
- Obtain a stage micrometer slide. BE VERY CAREFUL. A stage micrometer slide is costly, so please treat it with respect! Place the stage micrometer slide on the stage and focus on the millimeter markings using the 10x objective lens. Record the field diameter in mm when you use this lens in Table 3.
- Switch to the 40x objective lens and focus. Determine the field diameter in mm with the micrometer and record in table 3. Repeat the same steps for the other objective lenses.
- Convert the diameters to micrometers (μM). All cell and organelle measurements will be done in μM. Clean the slide carefully and place it back in its tray on the demo table.
|
Lens Used |
Total Magnification |
Diameter of Field (mm) |
Diameter of Field in (µm) |
|---|---|---|---|
Part III: Making Wet Mounts
Materials
|
|
Prepared Slides:
|
Procedure
Human Cheek Cells
The human cheek is lined with epithelial cells . They will be used today for you to observe a eukaryotic animal cells and its nucleus. You will scrape and stain a sample of your cheek cells with the dye methylene blue. The dye will allow you to clearly stain the nuclei of the cells. Be careful with the dyes used for the wet mounts as they will stain your skin and clothes. Also, the slides and coverslips you will use are stored in alcohol. Make sure to dry off the slides and coverslips with paper towels (not the expensive lens paper) before preparing your wet mount slides.
- Get a dry microscope slide and cover slip.
- Put a drop of methylene blue on the slide.
- Gently scrape the inside of your cheek with a toothpick and swirl it in the dye on the slide.
- Place a cover slip on the suspension and view at 1000X total magnification
- Draw 1-3 cells large enough to show the detail that you see in your lab manual. Label its cell membrane, cytoplasm and nucleus. Be sure to indicate the magnification used and specimen name. Also indicate the estimated cell size in micrometers under your drawing. See the example (which is missing the labels).
Elodea Leaf Wet Mount
The cell membrane is not visible on the Elodea leaf because of its proximity to the much thicker cell wall. In order to view the membrane, you will add salt to the Elodea . Water will flow out of the Elodea cells by osmosis, shrinking the cell membrane away from the stiff cell wall (plasmolysis).
- Get a microscope slide. Place 2 drops of dI water on the left and 2 drops 20% salt on the right.
- Obtain a leaf from a stalk of Elodea and cut the leaf in half. Place a half leaf in each solution.
- Wait 3-5 minutes and then place a cover slip over each leaf (dab off excess water).
- View at between 400X total magnification.
- Look for cells that have undergone plasmolysis. If none are found, prepare the slide again.
- Draw 2-3 connected cells large enough to show the detail that you see. Label the cell wall, cell membrane, cytoplasm, and chloroplasts in your lab manual. Be sure to indicate the magnification used and specimen name. Also indicate the estimated cell size in micrometers under your drawing.
Onion Membrane Wet Mount
Onion bulbs are actually swollen leaves that form an underground structure. Although not a good source for viewing chloroplasts, they are an excellent source for viewing eukaryotic plant nuclei.
- Get a dry microscope slide and cover slip.
- Cut a tiny square of one layer of the onion. Use forceps to peel the thin, white, transparent membrane from the inner concave side of an onion section (you only need a small piece, about the size of a pencil eraser) and place on slide. Try to smooth out the transparent onion membrane as flat as possible.
- Add a drop of iodine to the membrane and wait 30 seconds. Cover the membrane with a coverslip. Place the slide inside folded paper towel and pat gently for 1 second to remove excess dye.
- View at either 100X or 400X total magnification, so that you can see 2-3 cells.
- Draw 2-3 connected cells large enough to show the detail you see. Label the cell wall, nucleus, and cytoplasm . Be sure to indicate the magnification used and specimen name. Also indicate the estimated cell size in micrometers under your drawing.
Pond Water Wet Mount
You will prepare a wet mount of one of the following protists that can be found in pond water: Euglena, Spirogyra, Paramecium , and/or Amoeba .
- Get a depression slide and dry it off. The depression slide has a curved indent in the middle of the slide, which allows the living creatures to move around and not get squished.
- Put a drop of methyl cellulose and a drop from the pond water or cultures.
- Carefully put on a coverslip. If you have too much liquid on the slide, then gently use a corner of a paper towel to absorb the excess liquid.
- View at 100X or 400X total magnification.
- Draw the organisms that you see. Be sure to indicate the magnification used and specimen name. Also indicate the estimated cell size in micrometers under your drawing.
Prepared Slides
You will look at various prepared slides including Paramecium, Spirogyra , Human Blood Smears, Human Sickle Cell Red Blood Smears, Frog Blood Smears, and possibly others. View under the microscope using the highest magnification for the best cellular details and draw what you see. Be sure to indicate the magnification used and specimen name. Also, indicate the estimated cell size in micrometers under your drawing.
Part IV: Lab Check-out
Check off each task when complete. The instructor must sign before storing your microscope.
Returning Compound Microscope
- Rotate low power objective lens in position
- Use coarse focus to raise nosepiece to the top
- Remove slide from stage
- Be sure that the bar from stage clips does not stick out
- Turn rheostat to lowest before turning off the light
- Unplug and wrap power cord according to instructor’s instructions
- Carry microscope properly to cabinet and return to the correct shelf
Cleaning Wet Mounts
- Rinse slide in a beaker of water, remove and return cover slip and slide into the correct jars
- Put prepared slides back onto the correct tray on the demo table
- Tighten all reagent bottle caps.
- Clean up the demo table
- Wipe off all tables with wet sponge
Instructor Signature
Study Questions
- On the next page, label the parts of the microscope and list their function.
- How is a microscope properly carried?
- How is the microscope properly put away?
-
What is the magnification power of:
- High-power objective lens?
- Medium-power objective lens?
- Low-power objective lens?
- Ocular lens?
- How is the total magnification of a specimen determined?
- When the magnification increases, how does the size of the field of view change?
- Why is it important to place the medium on a slide before selecting the specimen to be mounted?
- Name one way to be sure the specimen will be found in the field of view when you change magnification.
- What are the distinguishing characteristics of a plant cell versus an animal cell?
- Knowing the size of the field of view using one of the three magnification lenses, be able to determine the size of a specimen being observed.